Memoirs of the Faculty of Engineering, Yamaguchi University

Back to Top
Permalink : https://petit.lib.yamaguchi-u.ac.jp/15610
Memoirs of the Faculty of Engineering, Yamaguchi University Volume 40 Issue 1
published_at 1989-10

Analysis of Particle Heating and Cooling in the Plasma Jet Reactor

プラズマジェット中に注入された粒子の加熱・冷却過程の解析
Sakiyama Satoshi
Onzuka Tatsunori
Sakai Hirotaka
Watanabe Makoto
Fukumasa Osamu
Osaki Katashi
Saeki Setsuo
fulltext
567 KB
KJ00000156784.pdf
About This Article
Descriptions
In the plasma processing with plasma jet reactors, powder materials are injected into the plasma flow. Then it is important to study interaction between the plasma flow and injected powder particles. In this paper, by using a single particle model for processing, we have calculated the temperature and the trajectry of the particle injected into the plasma flow at different pressures (760Torr, 100Torr) with various particle diameters (5μm&acd
Other Article
Structure of a d-type Rough Wall Turbulent Boundary Layer at a Low Reynolds Number : Higher order moments and violent events
PP. 1 - 7
Deflection of the Tooth of a Bevel Gear
PP. 9 - 14
Dynamic Vehavior of Sliding Clutch
PP. 15 - 25
Effects of Environments and Polarization Potential on the Stress Corrosion Cracking in High-Strength Aluminum Alloys
PP. 27 - 34
A Study on Characteristics of Noise Radiated from Mufflers with Air Flow (1st Report)
PP. 35 - 43
Application of Fuzzy Control to Fluidized Bed
PP. 45 - 54
Heat Transfer to Horizontal Finned Tube Bundles in the Freeboard Region of Fluidized Bed
PP. 55 - 62
Two-Dimensional Laminar Natural Convection Heat Transfer from a Fully or Partially Open Square Cavity
PP. 63 - 74
The Mechanism of Transportation inside the Screw Conveyer
PP. 75 - 81
Vibration of an Industrial Robot with a Flat Type Strain Wave Gearing
PP. 83 - 89
Experience-Based Concept Formation and Reasoning
PP. 91 - 95
Design of a Heat-Exchanger by Use of a Personal Computer, the M-Draf 16 and M-Draf 32 with their 2-D CAD Systems
PP. 97 - 106
Trajectory Control of an Industrial Robot (4th Report)
PP. 107 - 113
Measurement of Granular Surface Profile in a Hopper by Ultrasonic Linear Array Sensor
PP. 115 - 120
Improvement of the Efficiency in a Coal Gasification Process by Thermal Preconditioning of a Coal-Water Mixture
PP. 121 - 126
Ring Opening of 1,1-Dichloro-2-methyl-2-phenylsulfonylcyclopropane Derivatives with Sodium Alkoxide
PP. 127 - 137
Rotational Isomerism in Fluorene Derivatives XVIII : Conformational Equilibria of 9-Ary1-1-t-butylfluorene Derivatives
PP. 139 - 144
Effect of Initial Static Shear Stress on Undrained Cyclic Shear Deformation and Strength of Saturated Sand
PP. 145 - 159
On the Behavior of the Non-buoyant Jet Injected Into the Stream
PP. 161 - 165
Spreading of Oil Spilled on the Surface of Water Streaming
PP. 167 - 171
Membrane Effect on Liquefaction Resistance of Sand
PP. 173 - 179
Modified Beam Theory Considering Cross-Sectional Distortion of Thin-Walled Closed Section Beam and Its Application to Analysis of PC box Girders
PP. 181 - 187
The Quantification of Rill Patterns that Develop on Bare Hillslopes
PP. 189 - 196
Estimation of the Population in Yamaguchi Prefecture Considering the Inter-prefectural Migration
PP. 197 - 206
Resonant Phenomenon in the Overwrite Erasure Characteristics of Digital Magnetic Recording
PP. 207 - 212
Controll of Plasma Parameters in a Magnetically Filtered Multicusp Source
PP. 213 - 222
Measurement of Free Ca From Digital Images in Cultured Rat Brain Neurons
PP. 223 - 229
Improvement of Pixel Based Spatio-Temporal Correlation Analysis for Determining Optical Flow Velocity
PP. 231 - 239
Analysis of Particle Heating and Cooling in the Plasma Jet Reactor
PP. 241 - 248